EZ300 Pull Line Blower
The Pull Line Blower EZ300 by Zeitler needs no electrical connection. With the powerful 2-stroke engine, the pulling line is blown or sucked in independently of electricity.
The EZ300 is used for network construction in civil engineering, ground work, roads, tunnels, bridges, snow cannons and cable car construction.
It is suitable for cable ducts Ø 50 to 200 mm (internal diameter).
Water, small residues, impurities or else are ejected in the same operation.
- Blowing or sucking of cable pull line without compressor
- Power-independent thanks to 2-stroke engine
- Suitable for cords Ø 1mm to 5mm, with up to 600kg tensile strength
- For standard cable conduits from Ø 50 to 200 mm
- Ideally suited for installations in residential, commercial and industrial buildings, underground/road/tunnel/bridge construction, cable car construction and mountain railways
- For tube diffusers, cable conduits or occupied ducts
- Cleaning, ejecting water, calibrating and pulling in the cord in a single operation
- Powerful for pulling-in problems, such as crushed tubes
- Great time savings when pulling the cable in
- Easy operation and handling
- Light and compact
- Quickly ready for use
- Fast line feeding over 1’000m (current record 2850m)
- Excellent accessibility, even in confined spaces
- Fits in any car boot
- 1 x EZ300 Pull Line Blower
- 2 x Rolls of Cable Pull Line ca. 900m, tensile strength 24kg
- 5 x Shuttle complete set dimensions free of choice from ø 50-200mm
- 1 x Box with assembly material for shuttle
- 1 x Box with parachutes:
- 1 x for conduit ø 60 to 100 mm
- 1 x for conduit ø 100 to 150 mm
- 1 x Cone black for ducts ø 50 to 130 mm
- 1 x Special adapter for small tube ø 25-50 mm
- 1 x Head piece ø 140 mm with pull line supply
- 1 x Head piece ø 200 mm with pull line supply
- 1 x Suction unit
- 1 x Blowing unit
- 1 x Fuel can 0.5 liter (empty)
- 1 x Air hose 2m for extension
- 1 x Instruction manual
Weight of device: 5.7kg
Weight of device with carry-case: ca. 16kg
Dimensions of carry-case: 60x40x45cm
Engine: Single-cylinder two-stroke engine
Maximum air flow rate: Blowing mode 810 m³/h, Suction mode 770 m³/h
The use of the EZ300 Pull Line Blower
Experience the spectacular performance of the EZ300 Pull Line Blower from Zeitler
and get to know the world of cord blowing with the EZ300 Pull Line Blower Find out how this device can revolutionise your cable installation projects!
Water ejection with EZ300 Pull Line Blower
Convince yourself of the performance of the EZ300 from Zeitler!
This innovative device does not require an electrical connection and is equipped with a powerful 2-stroke engine, which enables blowing technique independent of electricity.
FAQ EZ300 Pull Line Blower
Yes, the EZ300 pull line blower can also be used with flexible pipes or corrugated pipes.
Yes, the EZ300 pull line blower can also be used with flexible pipes or corrugated pipes.
Yes, it is provided with the application of the shuttle.
The EZ300 pull line blower enables the pipes to be cleaned, water to be ejected, calibrated and the cord to be pulled in in a single operation using the blow-in shuttle.
Only if the pipe is not more than 50% full.
Additional accessories, such as a cone or a piece of pipe together with a foam insert, are required.
Yes, the cord is fed in from the outside and can therefore be reused.
The cone is perfect for use with poor pipe access or irregular pipe ends
The EZ300 pull line blower is equipped with the standard accessories for pipes with an internal diameter of Ø 50 to 200 mm.
For an extended application, an additional foam adapter is available, which enables use for pipes with a diameter of up to Ø 250 mm.